can i get to the gearbox and output gumph on a 650 by pulling off the bottom thus keeping the topend in one piece?
top end was done but when i rode it it sounds like the shaft or something up front is trying to make a break for it...
need a peek inside then the fuckers getting sold
650 motor strip question
Re: 650 motor strip question
Don't see why not. I did that on my 400/4..
GS650G - Biggest pile of crap on the planet
400FOUR (F2 in Candy Antares Red)
400FOUR (F2 in Candy Antares Red)
-
sparki
- Committee Member
- Posts: 1715
- Joined: Wed Nov 10, 2010 7:43 am
- Location: Derby, England
- Has thanked: 80 times
- Been thanked: 72 times
Re: 650 motor strip question
can on the 11's too but unsure about these... motors coming out anyway so what can it hurt to try eh 
-
sparki
- Committee Member
- Posts: 1715
- Joined: Wed Nov 10, 2010 7:43 am
- Location: Derby, England
- Has thanked: 80 times
- Been thanked: 72 times
Re: 650 motor strip question
took it to bits... i'm no expert but would say this is fucked lol
- Attachments
-
-
sparki
- Committee Member
- Posts: 1715
- Joined: Wed Nov 10, 2010 7:43 am
- Location: Derby, England
- Has thanked: 80 times
- Been thanked: 72 times
Re: 650 motor strip question
luckily (yeah right!) i have another piece of shit 650 motor in a corner with a wankered head on it... think that's coming apart too then for what is hopefully a decent shaft o gears n bits.
-
fossie
- Club Member
- Posts: 5182
- Joined: Sat Oct 23, 2010 9:16 pm
- Has thanked: 179 times
- Been thanked: 714 times
Re: 650 motor strip question
'Kin 'ell how on earth has the last owner done that? In 20 odd years of dispatching 650's I never , ever once needed to do anything to the shaft drive .......oh sorry once the seal at the wheel end went but just replaced the diff. No never even seen such a shitty piece of neglect, it can only have been shit riding. Explains the clutch issues as well eh?
-
sparki
- Committee Member
- Posts: 1715
- Joined: Wed Nov 10, 2010 7:43 am
- Location: Derby, England
- Has thanked: 80 times
- Been thanked: 72 times
Re: 650 motor strip question
yup... just when something is fixed on this another thing i havent looked at or repaired raises its head. nothing left now that i haven;t done.
fuckers getting sold when mot'd next week
i hate the fucking thing... picture JoihnR and his 400... well i feel the fucking same about this one
fuckers getting sold when mot'd next week
i hate the fucking thing... picture JoihnR and his 400... well i feel the fucking same about this one
-
sparki
- Committee Member
- Posts: 1715
- Joined: Wed Nov 10, 2010 7:43 am
- Location: Derby, England
- Has thanked: 80 times
- Been thanked: 72 times
Re: 650 motor strip question
the old crap engines gearbox looked ok though... it had better fucking work as it's back in the, what i hope is good, motor now... all teeth accounted for. it's sealed up and needs a little clean before it's back in the frame
-
johnr
- Club Member
- Posts: 3022
- Joined: Sun Oct 24, 2010 9:58 pm
- Location: lancashire
- Has thanked: 234 times
- Been thanked: 342 times
Re: 650 motor strip question
sparki wrote:yup... just when something is fixed on this another thing i havent looked at or repaired raises its head. nothing left now that i haven;t done.
fuckers getting sold when mot'd next week
i hate the fucking thing... picture JoihnR and his 400... well i feel the fucking same about this one
do
not
mention
me
and
fecking
400s
in
the
same
sentence......
actually, i quite like the 650s,,,,
